America Standards(TWP,GPT,HDT,TXL,TW) |
Remark:
The Standards is SAE J1128/1995
|
TWP,GPT,HDT with low Tension Strukture Parameter |
Cross Section mm2 |
SAE Gage No |
SAE Gage No |
SAE Wire Type |
TWP |
GPT |
HDT |
Wall Thickness mm |
Max. Diameter mm |
Wall Thickness mm |
Max. Diameter mm |
Wall Thickness mm |
Max. Diameter mm |
Nominal |
Min. |
Nominal |
Min. |
Nominal |
Min. |
0.22 |
24 |
7/0.20 |
0.40 |
0.28 |
1.50 |
/ |
/ |
/ |
/ |
/ |
/ |
0.35 |
22 |
7/0.25 |
0.40 |
0.28 |
1.70 |
/ |
/ |
/ |
/ |
/ |
/ |
0.5 |
20 |
7/0.32 |
0.40 |
0.28 |
1.90 |
0.58 |
0.41 |
2.40 |
0.91 |
0.64 |
3.10 |
0.8 |
18 |
16/0.25 |
0.40 |
0.28 |
2.20 |
0.58 |
0.41 |
2.50 |
0.94 |
0.66 |
3.40 |
1 |
16 |
16/0.30 |
0.40 |
0.28 |
2.40 |
0.58 |
0.41 |
2.90 |
1.02 |
0.71 |
3.70 |
2 |
14 |
40/0.25 |
0.40 |
0.28 |
2.70 |
0.58 |
0.41 |
3.20 |
1.04 |
0.73 |
4.20 |
3 |
12 |
60/0.25 |
0.45 |
0.32 |
3.30 |
0.66 |
0.46 |
3.80 |
1.17 |
0.82 |
5.10 |
5 |
10 |
95/0.25 |
0.50 |
0.35 |
4.00 |
0.79 |
0.55 |
4.70 |
1.17 |
0.82 |
5.70 |
8 |
8 |
103/0.30 |
0.55 |
0.39 |
4.90 |
0.94 |
0.66 |
6.00 |
1.40 |
0.98 |
7.00 |
|
| |
| TWP,TXL,TWE with Low Tension Structure Parameter |
Cross Section mm2 |
SAE Gage No |
Number Single wire/Diameter |
TWP?TXL?TWE |
Insulation Thickness mm |
Max. Diameter mm |
the smallest value |
the smallest average value |
Nominal |
0.22 |
24 |
7/0.20 |
0.28 |
0.32 |
0.40 |
1.48 |
0.35 |
22 |
7/0.25 |
0.28 |
0.32 |
0.40 |
1.63 |
0.5 |
20 |
7/0.32 |
0.28 |
0.32 |
0.40 |
1.85 |
0.8 |
18 |
16/0.25 |
0.28 |
0.32 |
0.40 |
2.12 |
1 |
16 |
16/0.30 |
0.28 |
0.32 |
0.40 |
2.25 |
2 |
14 |
40/0.25 |
0.28 |
0.32 |
0.40 |
2.66 |
3 |
12 |
60/0.25 |
0.32 |
0.35 |
0.45 |
3.20 |
5 |
10 |
95/0.25 |
0.35 |
0.40 |
0.50 |
3.88 |
8 |
8 |
103/0.30 |
0.39 |
0.44 |
0.55 |
4.70 |
|
| |
| American Standard STX |
Remark：
1、Standard：SAE J1127
2、Insulation：Flame resistant XLPE
3、Conductor：Annealed or Tinned Copper Wire
4、The heat resistance of XLPE：-40℃~125℃ or -40℃~150℃ |
| STX Structure Parameter |
Nominal Cross Section mm2 |
Conductor |
Insulation |
Single Wire |
Diameter of Lay Max. mm |
Length of Lay
Max. mm |
Cross Section |
Out Diameter mm |
Thickness Min. mm |
Number |
Diameter
max. mm |
Min. mm2 |
Nominal |
Tolerance |
8 |
133 |
0.27 |
3.9 |
Not Fixed |
7.6 |
1.2 |
-0.6 |
0.76 |
13 |
0.35 |
4.7 |
12.1 |
7.8 |
0.76 |
19 |
0.42 |
5.7 |
18.3 |
9.5 |
-0.8 |
0.78 |
32 |
665 |
0.25 |
8.0 |
31.1 |
11 |
40 |
779 |
0.254 |
8.8 |
38.1 |
12 |
50 |
1007 |
0.254 |
10.0 |
48.3 |
13 |
-1.0 |
62 |
1254 |
0.254 |
11.2 |
59.8 |
14.5 |
|
| |
| Besides standards listed above, we can also develop and produce different types of wires under customers’ request or, based on customers’ samples. |
